- Complete Kits
- Vape Juice
The lateral body adopts curve design to show its elegant lines. Super 225W output combining with the revolutionary SMOK TFV12 Prince tank will bring you ultimate vaping experience. It has an upgraded user interface and 1.3 inch screen with high-definition that displays more vaping data. Snake pattern on the back side is in harmony with the cobra drip tip, fully presenting your unique personal taste and charm.
Blade shaped areas on the front and back sides of Devilkin exude a supreme glory. The front "blade" functional area consists of TFT color screen and UP/Down button, which is more convenient to operate. The back "blade" snake pattern area will activate your vaping passion deep inside. You can enjoy 225W high wattage that powered by 2 x 18650 battery. Higher power output means massive clouds for you.
There are 3 modes for you: VW mode, TC mode (Ti, Ni, SS) and MEMORY mode.
Entirely new and upgraded UI provides you more direct and detailed vaping data. And there are six colors available for screen setting.
Supports Upgrading And Charging
Devilkin supports firmware upgrading, you can use the included USB port to upgrade it.
There's no need to change batteries frequently, the mod can be recharged via the Micro-USB port.
Devilkin provides multiple types of protection to avoid potential risks:
- Intelligent Atomizer Recognition
- Puff Monitoring System
- 10 Seconds Cut-off
- Short Circuit Protection
- Over-heating Protection
- Over discharge protection
Cobra Drip Tip
TFVI 2 Prince tank uses Cobra drip tip which has wild outlook and special tactility. Besides, it will bring you increased airflow.
Patented Locking Mechanism
The newly designed top cap has a patented locking mechanism, simply press this button then you can open the cap. Besides, this design can effectively avoid accidently opening of top cap and leaking of e-juice.
Top Refill System
Top rotary refill makes filling a easy thing. Leak proof slot can significantly solve leaking problem.
How to Refill SMOK Devilkin Kit
Hold the tank with one of your hands, use another one to press top cap and move it counterclockwise. Add e-liquid through the slot and pay attention not to drip it
into the central airflow tube. Close the cap carefully and firmly. Then let it stand for several minutes to get the organic cotton completely saturated.
How to Rebuild RBA
1. Before starting make sure your hands are clean.
2. Take RBA deck apart.
3. Place the coil between the posts and wrap the ends around the screws and tighten up, once all in place make sure the coil is fixed in the center and lined up with the air hole, and also make sure the coil is NOT touching the base.
Cut a strip of cotton and make sure it's not too much and not too little.
4.Insert the cotton and placing it in the middle. Cut the cotton at an angle and make sure it's not too short and not too long. Wet the coil with your e-liquid and adjust the cotton.
Warning: Coils must be checked for resistance before they are fired on a device,
and rechecked periodically to ensure the resistance remains the same.
- Tank Capacity: 8ml
- Tank Size: 28 x 63mm
- Mod Size: 86 x 49.6 x 34.2mm
- Power Range: 1W-225W
- Standby Current: <500μA
- Output Voltage: 0.5V-9.0V
- Resistance Range: 0.1Ω-2.5Ω(VW)/0.05Ω-2.0Ω(TC)
- Temperature Range: 200°F-600°F/100°C-315°C
- 1x Devilkin Mod
- 1x SMOK TFV12 Prince Tank
- 1x V12 Prince-Q4 0.4 ohm Quadruple Coils(pre-installed)
- 1x V12 Prince-T10 0.12 ohm Decuple Coils
- 1x Replacement Glass Tube
- 1x USB Cable
- 1x User Manual
- 1x Set of Spare Parts
No - 2 x 18650 Batteries sold separately